Based in Enfield. Working across Adelaide and regional SA. 08 8151 1040

How often does test and tag need to be done in Adelaide?

It depends on the environment: SafeWork SA's guidance is at least every 3 months on construction and demolition sites, every 6 months in manufacturing and commercial cleaning, and at least every 12 months in other hostile environments. Hire equipment is inspected before each hire and tested every 3 months, and test and tag with VD Fire & Electrical starts from $3.50 + GST per item.

In South Australia, test and tag is due every 3 months on construction sites, every 6 months in factories, workshops and commercial cleaning, and at least every 12 months in other hostile environments. Hire equipment is inspected before each hire and tested every 3 months, and low-risk office equipment can go up to 5 years.

There’s no single answer for every business. The interval depends on the type of workplace and how hard the equipment gets used, and the riskier the setting, the more often you test.

What test and tag covers

Test and tag, more formally the in-service inspection and testing of electrical equipment, covers plug-in equipment: power leads, extension cords, power boards and appliances. A technician checks each item for damage and runs electrical tests, then attaches a tag showing who tested it and when. It does not cover fixed wiring, only equipment that plugs into a socket.

How often test and tag is required in Adelaide

SafeWork SA’s inspection and testing guidance sets general rules by environment, and points to AS/NZS 3760:2022 for the detail:

  • Construction and demolition sites: every 3 months for portable equipment, and every 6 months for transportable structures, fixed equipment and construction wiring.
  • Manufacturing and workshop environments: at least every 6 months.
  • Commercial cleaning equipment: every 6 months.
  • Other hostile operating environments: at least every 12 months. This covers equipment exposed to moisture, heat, vibration, mechanical damage, corrosive chemicals or dust.
  • Residential type areas such as hotels, motels, hostels and boarding houses: every 2 years.
  • Hire equipment: inspected before each hire and tested every 3 months. During the hire, the business using it should make sure it meets the testing rules for its own workplace.
  • Offices and low-risk areas: SafeWork SA’s table lists up to 5 years where equipment is not flexed in normal use, not open to abuse and not in a hostile environment.

So a builder and an accountant have very different obligations. If you’re arranging testing across mixed spaces, such as a workshop with an office attached, different areas may fall on different schedules. These are general rules: your risk assessment, industry or insurer may call for something stricter, and SafeWork SA says the class of work and the risks of the equipment determine how often it is tested.

What the testing and tagging process involves

Electrical test and tag is quick per item but thorough:

  • A visual inspection for damaged plugs, cords, casings and strain reliefs.
  • Electrical tests with a portable appliance tester, such as earth continuity and insulation resistance where they apply to the item.
  • Recording who tested each item, the date, the result and when the next test is due. WHS regulation 150 allows that record to be a tag, and most businesses also keep a register.
  • Taking anything that fails out of service for repair, replacement or disposal.

The visual check catches a surprising amount. A lot of failures are just cracked plugs or damaged leads. RCD testing is usually done on the same visit, because AS/NZS 3760 covers both.

Compliance requirements and standards

AS/NZS 3760 is the standard most people mean when they talk about test and tag. It isn’t law on its own, but SafeWork SA’s Code of Practice on managing electrical risks refers to it for guidance on testing, so it is the accepted way to show you have met your duty. The legal duties sit in the Work Health and Safety Regulations 2012 (SA):

  • Regulation 150 requires plug-in equipment used in hostile operating environments to be regularly inspected and tested by a competent person.
  • Regulations 163 to 165 cover construction work (which must follow AS/NZS 3012), the use of RCDs, and RCD testing.

Even where the regulations don’t require testing, every business has a general duty to keep electrical equipment safe. Keeping a register of results is how you show it. If there’s a SafeWork SA visit or an electrical incident, that record shows the equipment was maintained.

Signs an appliance needs checking sooner

Between scheduled tests, pull an item from use and have it checked if you spot:

  • A cracked or damaged plug, or exposed wiring at the cord.
  • A lead that has been taped up, kinked, or run over repeatedly.
  • Scorch marks, melting, or a burning smell from a plug or appliance.
  • A tag that is missing or past its due date on equipment in daily use.

Damaged leads are the most common hazard, and they’re easy to spot once you’re looking.

Match the effort to the risk. Check the busy, high-wear gear often and you’ll stay safe and compliant without over-servicing the rest. See our guide to test and tag colours for what the coloured tags on building sites mean, or call VD Fire & Electrical on 08 8151 1040 to book test and tag.

Frequently asked questions

How often does test and tag need to be done on a construction site in SA?
Every 3 months for portable equipment. SafeWork SA's table for construction and demolition sites lists 3 months for portable electrical equipment and 6 months for transportable structures, fixed equipment and construction wiring. Its construction guideline adds a visual safety check before each use.
Is test and tag a legal requirement in South Australia?
The WHS Regulations require plug-in equipment used in hostile operating environments, such as where it is exposed to moisture, heat, vibration, mechanical damage, corrosive chemicals or dust, to be regularly inspected and tested by a competent person. AS/NZS 3760 is the guidance SafeWork SA uses for how often.
How often should office equipment be tested and tagged?
SafeWork SA's table, based on AS/NZS 3760, lists up to 5 years for equipment that is not flexed in normal use, not open to abuse and not in a hostile environment, which describes much office equipment. A risk assessment may still call for shorter intervals for items that are moved around a lot.
How often does hire equipment need to be tested?
SafeWork SA's code of practice says hired equipment should be inspected at the start of each hire and tested every 3 months. During the hire, the business using it should make sure it meets the testing rules for its own workplace.
What does a test tag need to show?
WHS regulation 150 says the test record must show who did the test, the date, the outcome and the date the next test is due. The record can be a tag on the equipment. On construction sites, SafeWork SA's guideline recommends tags colour-coded by the quarter the test was done.

Book your next service

Tell us what's on site and we'll send a fixed price the same day.

Call 08 8151 1040 Get a quote