Based in Enfield. Working across Adelaide and regional SA. 08 8151 1040

How often RCD testing is legally required in Adelaide

In a South Australian workplace, WHS regulation 165 requires RCDs (safety switches) to be tested regularly by a competent person, with a record kept of every test other than daily ones. How often depends on the environment: SafeWork SA's guidance runs from a push-button test before each use on building sites to an operating-time test every 2 years in an office.

In South Australian workplaces, RCDs must be tested regularly by a competent person under the Work Health and Safety Regulations 2012 (SA). SafeWork SA’s guidance sets how often, from a push-button test before each use on building sites to an operating-time test every 2 years in an office.

The rules are more straightforward than they first look.

What an RCD, or safety switch, does

An RCD (residual current device), the “safety switch” in your switchboard or on a portable lead, constantly monitors the current flowing in a circuit. If it detects current leaking to earth, such as through a person receiving a shock, it cuts the power in a fraction of a second. That fast trip is what stops a shock becoming fatal. An RCD test checks that it still happens.

RCDs come as fixed devices (built into the switchboard or a fixed socket) and portable devices (plug-in units and RCD-protected power boards). The two are tested on different schedules.

How often RCD testing in Adelaide is required

The law sets the duty. The guidance sets the interval. WHS regulation 165 says RCDs must be “tested regularly by a competent person” but does not give a number. SafeWork SA’s inspection and testing guidance and its Code of Practice on managing electrical risks point to AS/NZS 3760 for the intervals. There are two tests:

  • Push-button test. The user presses the “test” button to confirm the RCD trips.
  • Operating-time test. A competent person uses an instrument to measure how quickly the RCD trips, and confirms it is within the limit for its type.

How often each is done depends on where the RCD is used:

Environment Push-button test Operating-time test Source
Construction and demolition sites, fixed RCDs Monthly At least every 12 months SafeWork SA construction guideline
Construction and demolition sites, portable RCDs Before use, first time each day At least every 3 months SafeWork SA construction guideline
Factories, workshops, places of manufacture or maintenance, portable RCDs Daily, or before every use, whichever is longer Every 12 months SafeWork SA table
Offices and other areas where equipment is not flexed, not open to abuse and not in a hostile environment Portable every 3 months, fixed every 6 months Every 2 years SafeWork SA table

Because the intervals shift with the type of workplace, confirm the schedule for each area of your site rather than assuming one figure covers everything. A workshop with an office upstairs can sit on two schedules. A documented risk assessment by a competent person can also justify a different interval.

At home there’s no legal testing interval. SA.GOV.AU advises testing your safety switches twice a year, and suggests doing it when the clocks change for daylight saving.

What RCD safety switch testing involves

RCD safety switch testing is quick per device but methodical:

  • Locating and identifying each RCD in the switchboard and on portable equipment.
  • Pressing the test button to confirm it trips.
  • Using an RCD tester to measure the trip time against the limit for the device type.
  • Recording the result against each device.
  • Flagging any RCD that trips too slowly, or not at all, so it can be taken out of service and replaced.

It’s usually done alongside test and tag of portable equipment, since AS/NZS 3760 covers both. Testing a fixed RCD briefly cuts power to the circuits it protects, so it’s worth planning around computers, fridges and anything else that shouldn’t lose power unexpectedly.

Compliance requirements and standards

Three regulations do most of the work in South Australia:

  • Regulation 164 requires RCD protection on socket outlets in higher-risk situations, such as hostile operating environments and equipment that is moved around in ways likely to damage it or its cord.
  • Regulation 165 requires RCDs to be tested regularly by a competent person, and a record kept of every test other than daily tests until the device is next tested or permanently removed from use.
  • Regulation 163 requires construction work to follow AS/NZS 3012, the standard for electrical installations on construction and demolition sites.

SafeWork SA’s code of practice adds that a faulty RCD must be taken out of service and replaced as soon as possible. AS/NZS 3760 is not law on its own, but SafeWork SA’s code and guidance call it up, so it is the accepted way to show you met the regulation.

The record matters. If there’s an electrical incident or a SafeWork SA visit, being able to show your RCD testing was kept up to date is how you show you met your duty. See our guide to test and tag intervals for the portable-equipment side of the same duty.

Signs your safety switch needs a check sooner

Don’t wait for the next scheduled test if you notice:

  • A safety switch that won’t stay reset, or trips repeatedly for no obvious reason.
  • An RCD that doesn’t trip when you press its test button.
  • Burning smells, buzzing, or scorch marks around the switchboard.
  • No safety switches at all on the power and lighting circuits of an older building.

Any of these warrants a licensed electrician sooner rather than later. A switchboard fault or missing RCD is electrical work, not a testing job.

Testing RCDs on schedule takes a few minutes per device, and it could save a life. VD Fire & Electrical tests RCDs alongside test and tag across Adelaide. See RCD testing, call 08 8151 1040 or ask for a quote.

Frequently asked questions

Is RCD testing a legal requirement in South Australia?
Yes, for workplaces. WHS regulation 165 says a person with management or control of a workplace must take all reasonable steps to ensure RCDs used there are tested regularly by a competent person, and must keep a record of each test (other than daily tests) until the device is next tested or permanently removed from use.
How often should RCDs be tested in an office?
SafeWork SA's table, which follows AS/NZS 3760, lists a push-button test every 3 months for portable RCDs and every 6 months for fixed RCDs, plus an operating-time test every 2 years, for low-risk areas like offices where equipment is not flexed, not open to abuse and not in a hostile environment.
How often are RCDs tested on a construction site?
SafeWork SA's construction guideline says fixed RCDs get a push-button test monthly and a performance (trip-time) test at least every 12 months. Portable RCDs are push-button tested before use each day and performance tested at least every 3 months.
How often should I test the safety switch at home?
There is no testing law for homes, but SA.GOV.AU advises pressing the test button on your safety switches twice a year, for example when the clocks change for daylight saving. If a switch doesn't trip, call a licensed electrician.
Who can test RCDs in a workplace?
A competent person: someone with the knowledge and skills, from training, qualification or experience, to test RCDs and use the instruments correctly. The daily or monthly push-button test can be done by the user.

Book your next service

Tell us what's on site and we'll send a fixed price the same day.

Call 08 8151 1040 Get a quote