VD Fire & Electrical’s 6-monthly fire extinguisher service starts from $9 + GST per extinguisher in Adelaide. Your total depends on how many extinguishers you have, what types they are and whether a yearly or 5-yearly service is due.
There’s no single price for every site. Here is what you’re paying for, so the number on your invoice makes sense.
What fire extinguisher testing covers
Fire extinguisher testing is the routine servicing that confirms each unit will work when someone grabs it in an emergency. A technician checks the pressure, the physical condition, the mounting and signage, and, at the longer intervals, the internal components, then records the service on the unit’s tag. It’s an ongoing maintenance cycle rather than a one-off job.
What affects your fire extinguisher service cost
Several things move the price up or down, which is why a flat “per building” figure is rarely accurate:
- The number and type of extinguishers. Water, foam, CO2, dry powder and wet chemical units each have slightly different service needs.
- Which service is due. A 6-monthly inspection is the quickest. The yearly service takes longer, and the 5-yearly service, the most involved in the cycle, costs more again.
- Site access and travel. A single small office is quicker to service than a multi-level site with extinguishers spread across floors.
- Refills and replacements. Any unit that has been used, has lost pressure or fails inspection needs refilling, recharging or replacing.
The most reliable way to know your cost is a quote based on an actual list of your equipment. If you’re comparing prices, make sure each quote covers the same scope. A cheap headline rate can leave out the 5-yearly services or refills you’ll still need to pay for.
We quote yearly and 5-yearly services, refills and replacements per site, once we know what you have.
How often testing is required
South Australia’s maintenance standard is MBS 002 (version 3, May 2023). It replaced SA 76 and calls up AS 1851-2012, the Australian Standard for routine service of fire protection systems and equipment. For portable fire extinguishers, that means:
- Every 6 months: an inspection of every unit.
- Every year: a more thorough service.
- Every 5 years: the most thorough service in the cycle.
So across a five-year period you’re paying for regular 6-monthly and yearly services plus one larger 5-yearly service per unit, not a single annual fee.
What a fire extinguisher inspection in Adelaide involves
A standard fire extinguisher inspection follows the same core steps:
- Confirming the extinguisher is the right type and correctly located for the risk.
- Checking the pressure gauge, safety pin, tamper seal, hose and nozzle for damage or wear.
- Weighing or checking the charge where required.
- Inspecting the mounting bracket, signage and access.
- Tagging the unit and recording the service so there is a clear history.
Every service is logged, which matters for the next point.
Compliance requirements and record-keeping
Fire extinguishers are essential safety provisions (ESPs). For most larger buildings, the owner must lodge a Form 3 with council each year, within 60 business days after the end of the calendar year, confirming the ESPs were maintained and tested. Your service records are the evidence behind that certificate.
Smaller buildings may be exempt from lodging: Class 1b buildings, and Class 3 to 9b buildings with a rise of 2 storeys or less and a floor area of 500 m² or less, unless a section 157 notice or a performance solution applies. Exempt owners must still maintain their ESPs (regulation 94).
Not lodging a Form 3 or not maintaining ESPs carries a $750 expiation and a maximum penalty of $10,000 (regulation 94 of the Planning, Development and Infrastructure (General) Regulations 2017). A missing record can also cause problems with an insurer after a fire. None of that is an issue if the servicing is done on time. That’s what the 6-monthly cycle is for.
Signs an extinguisher needs attention before its next service
You don’t have to wait for the scheduled visit if you spot something obviously wrong. Book a check sooner if:
- The pressure gauge needle sits outside the green band.
- The unit has visible rust, dents, or a cracked or perished hose.
- The safety pin or tamper seal is missing or broken.
- The service tag is missing, unreadable, or past its due date.
- The extinguisher has been used, even briefly.
Any of these is worth flagging rather than assuming the extinguisher is fine.
Extinguisher testing is one of the cheaper parts of staying compliant, and once you know what drives the cost it’s easier to budget for. For a quote based on your actual equipment list, call VD Fire & Electrical on 08 8151 1040 or request a quote. See our fire extinguisher testing service for what each visit includes, and our guides to fire extinguisher expiry and extinguisher types and colours for what to check on your own units.