To change a smoke alarm battery, take the alarm off its ceiling base, replace the battery with the type the instructions list, put the alarm back and press the test button. On a sealed 10-year alarm you can’t change the battery, so you replace the alarm. On a hardwired alarm you turn the power off first and leave the base and wiring alone.
The steps below match the instructions from the main brands sold in Australia. Always check the leaflet or label for your model, because the way the alarm comes off its base varies.
What kind of smoke alarm do you have?
Look at the alarm before you climb up.
- Hardwired (240 V) alarm. It has a steady green light while mains power is on. Its backup battery is either a replaceable 9-volt battery or a sealed rechargeable lithium battery that lasts the life of the alarm (Brooks).
- Replaceable battery alarm. Usually a 9-volt battery, changed every year.
- 10-year lithium alarm. The battery is sealed in and can’t be removed or replaced. The label shows a “replace by” date.
If you can’t tell, the brand and model are printed on the label on the back or side, and the maker’s website will have the instructions.
How do you open a smoke alarm?
Most alarms come away from a base plate screwed to the ceiling.
- Battery alarms usually twist anticlockwise off the base, and twist back on to switch on (Red).
- Hardwired alarms either slide off the base, sometimes with a flat screwdriver in a marked release slot (Brooks), or hinge open and hang from the base (Red).
Don’t force it or prise the base off the ceiling. If it won’t come away the way the instructions describe, stop and get help.
How do you change a 9-volt smoke alarm battery?
- Get the right battery. Buy the battery type listed in the instructions. Quell says its alarms are certified to be used with the battery models specified in the user manual.
- Set up safely. Use a stable step ladder rather than a chair.
- Take the alarm off its base by twisting or sliding it, as described above.
- Take out the old battery. Unclip it gently. Brooks warns that damage to the battery clip or wires causes constant beeping and means the alarm has to be replaced.
- Drain the alarm. With the battery out, hold the test button down. Red says to hold it for 10 seconds to drain any remaining power, and Quell says holding it for at least 15 seconds resets an alarm that has stored a low battery warning.
- Fit the new battery the right way round. It only goes in one way (Red).
- Refit the alarm on its base. Many alarms won’t go back on without a battery fitted.
- Test it. Press and hold the test button until the alarm sounds (MFS). If your alarms are interconnected, the others should sound too.
How do you change the backup battery in a hardwired smoke alarm?
The same steps apply, with two extra rules. Turn the power off first, and never touch the base or wiring.
- Check whether there’s anything to change. Alarms with a sealed rechargeable backup battery have no battery to replace. If one of these chirps, see why a smoke alarm beeps or chirps.
- Turn off the power to the alarms at the switchboard. Brooks says to turn off mains power before removing the alarm, and the green light goes out.
- Slide or hinge the alarm off its base and change the 9-volt battery as above.
- Refit the alarm, turn the power back on and check the green light is lit.
- Test the backup battery. The MFS says to test it by switching off the power at the main switch or circuit breaker and then pressing the test button. Turn the power back on afterwards.
The base carries 240 V. Undoing it, moving it or replacing a hardwired alarm is electrical work. In South Australia a qualified electrician must install hardwired alarms, and the electrician issues an electronic Certificate of Compliance for the work.
What about 10-year lithium smoke alarms?
There is no battery to change. When a sealed alarm chirps for a low battery, or passes its “replace by” date, the whole alarm is replaced (Red). Battery powered alarms can be fitted by the householder, following the manufacturer’s instructions (MFS).
Replace like with like. If your home was built from 1 January 1995, South Australian law requires hardwired alarms, so a sealed battery alarm isn’t a legal substitute for a hardwired one. The MFS smoke alarm legislation fact sheet sets out which type each home needs.
How often should you change smoke alarm batteries?
Once a year, or straight away if the alarm gives a low battery beep. That includes the replaceable backup batteries in hardwired alarms. The MFS suggests doing it when you change your clocks back at the end of daylight saving, and testing each alarm once a month. Every alarm, whatever its battery, should be replaced at least every 10 years.
When should you call someone in?
Call a professional if the alarm is hardwired and needs replacing, if it keeps chirping after a new battery, if you can’t reach it safely, or if you look after alarms in a rental. Landlords can read our guide to smoke alarm rules for SA landlords.
VD Fire & Electrical’s annual smoke alarm testing starts from $89 + GST per property, and hardwired replacements are done by our licensed electrical contractor.